2020 Kenworth W900 Recalls

PACCAR Incorporated (PACCAR) is recalling certain 2020 Kenworth T660, 2018-2024 Kenworth T800 and W900 vehicles. An additional spacer may have been added to the joint that connects the seat to the seat belt tether and buckle, causing an unsecured connection.

An unsecured seat belt connection may not properly restrain an occupant during a crash, increasing their risk of injury.

Dealers will inspect and remove the additional spacer and replace the bolt, as necessary, free of charge. Owner letters were mailed March 20, 2024. Owners may contact PACCAR's customer service at 1-425-828-5888. PACCAR's number for this recall is 23KWK.

PACCAR Incorporated (PACCAR) is recalling certain 2018-2020 Kenworth T270, T370, T440, T470, T660, T680, T880, T800, W900, W990; and 2018-2020 Peterbilt 330, 337, 348, 365, 367, 389, 520, 567, and 579 vehicles. The Dana D-Series axle steer arm fasteners that attach the steering arm to the steering knuckle may fail.

Fastener failure can result in a loss of steering control, increasing the risk of a crash or injury.

Dealers will replace and torque the steer arm fasteners, at no charge. Owner notification letters were mailed November 8, 2022. Owners may contact Kenworth customer service at 1-425-828-5888 and Peterbilt customer service at 1-940-591-4220. PACCAR's numbers for this recall are 22 PBB and 22 KWB.

PACCAR Incorporated (PACCAR) is recalling certain 2020-2021 Peterbilt 348, 365, 367, 389, 520, 567 and Kenworth T800, T880, W900, W990 vehicles equipped with Watson and Chalin steerable lift axle suspension systems (model SL2065). The axles may have lower rear pivot bolts that are not long enough to sufficiently…

The short screws can cause the hardware to separate from the suspension system and become road hazards, increasing the risk of a crash and/or injury.

PACCAR will notify owners, and dealers will inspect suspect chassis and replace the pivot bolts, as necessary, free of charge. The recall began September 29, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 and Peterbilt customer service at 1-940-591-4220. PACCAR's numbers for this recall is…

PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System…

If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at…

PACCAR Incorporated (PACCAR) is recalling certain 2020 Peterbilt 520 and 579 vehicles and Kenworth T680, T880 and W990 vehicles. The mirror glass may detach from the mirror carrier plate due to inadequate adhesion.

If the mirror glass detaches, the driver may have reduced visibility and the mirror glass will become a road hazard that may strike another vehicle or pedestrian, increasing the risk of a crash or injury.

PACCAR has notified owners, and dealers will inspect the upper mirror glass/mirror carrier, replacing it as necessary, free of charge. The recall began May 31, 2019. Kenworth owners may contact PACCAR customer service at 1-425-828-5888 and Peterbilt owners may call 1-940-591-4220. PACCAR's numbers for this recall…

PACCAR Incorporated (PACCAR) is recalling certain 2020 Kenworth T680, T800, T880, W900 and W990 trucks. The rear axles may not contain oil.

Without lubricating oil, the bearings, hub and axle shafts may wear, resulting in the separation of a wheel end from the axle, increasing the risk of a crash.

Paccar will notify owners, and Kenworth dealers will inspect all of the rear axles for the presence of oil. If no oil is present, the wheels ends will be removed and the bearings, hub and axle shaft will be inspected for damage. If excessive wear or heat damage is evident, the components will be replaced, as…