The 2008 Mack Cxn has 5 NHTSA recall campaigns affecting an estimated 76,929 vehicles. Recall repairs are always free at any authorized dealer. Last updated July 6, 2026.
MACK IS RECALLING 34,269 MY 1999-2005 CX AND MY 2004-2008 CXN TRUCKS. THE HEADLIGHT SWITCH MAY PREMATURELY FAIL RESULTING IN INOPERATIVE OR INTERMITTENT HEADLIGHTS.
THE HEAD LIGHTS MAY NOT OPERATE PROPERLY WHICH COULD RESULT IN INTERMITTENT OR NO HEADLIGHT FUNCTION. THIS COULD IMPAIR A DRIVER'S VISIBILITY, INCREASING THE RISK OF A CRASH.
DEALERS WILL REPLACE THE HEADLIGHT SWITCH. THE RECALL BEGAN ON FEBRUARY 27, 2009. OWNERS MAY CONTACT MACK AT 1-800-528-6586.
ON CERTAIN TRUCKS, THE BOLTS THAT ATTACH THE STEERING GEAR TO THE FRAME MAY NOT HAVE BEEN TIGHTENED TO THE SPECIFIED TORQUE.
LOSS OF STEERING CONTROL COULD OCCUR INCREASING THE RISK OF A CRASH.
DEALERS WILL TIGHTEN THE BOLTS FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 10, 2007. OWNERS MAY CONTACT MACK TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS EQUIPPED WITH A SAF HOLLAND SIMPLEX FIFTH WHEEL, THE LEVER ARM PIVOT BOLT MAY HAVE BEEN OVER TIGHTENED. AN OVER TIGHTENED PIVOT BOLT CAN DISTORT THE PIVOT BOLT SPACER SLEEVE, WHICH MAY PREVENT THE FIFTH WHEEL LATCH JAW FROM CLOSING AND LATCHING SECURELY AROUND THE TRAILER KING PIN.
THERE IS A POSSIBILITY THAT THE PIVOT BOLT CAN BECOME LOOSE WITHOUT THE DRIVER'S KNOWLEDGE. WHEN THIS OCCURS, THE DRIVER COULD DRIVE AWAY AND THE TRAILER COULD BECOME DISENGAGED, INCREASING THE RISK OF A CRASH.
DEALERS WILL REPLACE THE PIVOT BOLT AND SLEEVE WITH A HEX HEAD SHOULDER BOLT AND WASHER FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 28, 2008. OWNERS MAY CONTACT MACK TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS EQUIPPED WITH PARKER SINGLE CHECK VALVES (SCV) PROVIDED BY BENDIX. THE DEFECT EXISTS IN THE PARKER SCV THAT CONNECTS WITH THE SUPPLY PORT OF THE SR-7 SPRING BRAKE MODULATING VALVE. AFTER PROLONGED USE OF THE PARKER SCV, THE VALVE BODY RETAINER MAY BECOME EXCESSIVELY WORN AND EVENTUALLY BREAK…
THIS CONDITION CAN CAUSE A DELAY IN THE APPLICATION OF THE SPRING BRAKES TO PARK THE VEHICLE AFTER THE OPERATOR PULLS THE DASH VALVE BUTTON. THESE CONDITIONS CAN OCCUR WITHOUT WARNING, LEADING TO UNINTENDED VEHICLE ROLLAWAY, BRAKE DRAG, OR IN THE CASE OF LOSS OF PRIMARY CIRCUIT, INABILITY TO MODULATE THE SPRING…
MACK IS WORKING WITH BENDIX TO REPLACE THE PARKER SINGLE CHECK VALVE. THE RECALL BEGAN ON JANUARY 9, 2008. OWNERS MAY CONTACT BENDIX AT 1-440-329-9000 OR MACK AT 1-800-528-6586.
ON CERTAIN TRUCKS EQUIPPED WITH BENDIX SR-7 SPRING BRAKE MODULATING VALVES, THE INTERNAL RUBBER CHECK VALVE MAY LEAK CAUSING A DELAY IN THE APPLICATION OF THE SPRING BRAKES TO PARK THE VEHICLE AFTER THE OPERATOR PULLS THE DASH VALVE BUTTON.
THIS COULD DELAY OR FAILURE IN APPLYING THE PARKING BRAKES WHICH COULD RESULT IN A VEHICLE ROLL AWAY, INCREASING THE RISK OF A CRASH.
MACK IS WORKING WITH BENDIX TO REPAIR THESE VEHICLES (PLEASE SEE 07E037). BENDIX WILL INSTALL A CHECK VALVE REPAIR KIT FOR THE AFFECTED SR-7 SPRING BRAKE MODULATING VALVE FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 10, 2008. OWNERS MAY CONTACT BENDIX AT 1-440-329-9000 OR MACK AT 1-800-528-6586.
Recall, complaint, and investigation records from official NHTSA datasets (FLAT_RCL, FLAT_CMPL, FLAT_INV), synced weekly. Counts reflect NHTSA records for the 2008 Mack Cxn as of July 6, 2026. Complaint narratives are consumer-submitted and unverified. This page contains ads and affiliate links. Full methodology.